单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related confi

题目
单选题
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable
A

RIPng will be enabled on no interfaces.

B

RIPng will be enabled on one interface.

C

RIPng will  be enabled on two interfaces.

D

RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.

相似考题

1.The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1A. Automatic 6to4B. Manually configured tunnelC. ISATAPD. GRE

2.Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0A. OSPF works on F0/0 and S0/0/0 without further configurationB. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modEC. OSPF works with the addition of one command: an router - id command in OSPF router configuration modED. OSPFv3 needs at least two more configuration commands before it works on R1

3.Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2‘s F0/0 interface. Which of the following is true about R1‘s route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64A. The next hop is 2000::1311:11FF:FE11:1111B. The next hop is FE80::1311:11FF:FE11:1111C. The next hop is FE80::5111:11FF:FE11:1111D. The next hop is 2001::1

4.Router R1 has been conf igured with an ipv6 route 2000::／64 S0／0／0 64 command.Which of the following does the 64 at the end of the command represent?()A. MetricB. Administrative distanceC. Timeout (seconds)D. Prefix lengthE. Interface ID

更多“单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related confi”相关问题

  • 第1题：

    Router R1 has the following configuration. Assuming R1‘s F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64

    A. 2345:0:0:8::1

    B. 2345:0:0:8:0:FF:FE11:1111

    C. FE80::8:0:FF:FE11:1111

    D. FE80:0:0:8::1


    参考答案：A, C

  • 第2题：

    Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.Which of the following is true about how IOS tries to limit EIGRP‘s use of bandwidth on S0/0?（）

    A.R1 limi ts EIGRP to around 250Kbps on DLCI 102

    B.R1 limits EIGRP to around 250Kbps on DLCI 104

    C.R1 limits EIGRP to around 150Kbps on every DLCI

    D.R1 does not limit EIGRP because noWAN bandwidth control has been configured


    参考答案：A

  • 第3题：

    Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1‘s (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode.Which of the following occurs？（）

    A.Fa0/0 fails

    B.The command is rejecteD

    C.The existing three neighbors fail

    D.The neighborship with 172.16.2.20 fails and then reestablishes

    E.None of the other answers is correct


    参考答案：C

  • 第4题：

    Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）

    • A、R1 limi ts EIGRP to around 250Kbps on DLCI 102
    • B、R1 limits EIGRP to around 250Kbps on DLCI 104
    • C、R1 limits EIGRP to around 150Kbps on every DLCI
    • D、R1 does not limit EIGRP because noWAN bandwidth control has been configured

    正确答案:A

  • 第5题：

    Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）

    • A、Metric
    • B、Administrative distance
    • C、Timeout (seconds)
    • D、Prefix length
    • E、Interface ID

    正确答案:B

  • 第6题：

    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable

    • A、RIPng will be enabled on no interfaces.
    • B、RIPng will be enabled on one interface.
    • C、RIPng will  be enabled on two interfaces.
    • D、RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.

    正确答案:B

  • 第7题：

    单选题
    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable
    A

    RIPng will be enabled on no interfaces.

    B

    RIPng will be enabled on one interface.

    C

    RIPng will  be enabled on two interfaces.

    D

    RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.


    正确答案： D
    解析： 暂无解析

  • 第8题：

    单选题
    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0
    A

    OSPF works on F0/0 and S0/0/0 without further configuration

    B

    OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE

    C

    OSPF works with the addition of one command: an router - id command in OSPF router configuration modE

    D

    OSPFv3 needs at least two more configuration commands before it works on R1


    正确答案： B
    解析： 暂无解析

  • 第9题：

    单选题
    The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（） interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 2 ipv6 address 2002:C0A8:10 1::1/64 tunnel source loopback 1
    A

    Automatic 6to4

    B

    Manually configured tunnel

    C

    ISATAP

    D

    GRE


    正确答案： C
    解析： 暂无解析

  • 第10题：

    单选题
    Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（） interface f0/0 mac - address 1111.1111.1 111 ipv6 address 2000::/64 eui - 64 ipv6 address 2001::1/64
    A

    The next hop is 2000::1311:11FF:FE11:1111

    B

    The next hop is FE80::1311:11FF:FE11:1111

    C

    The next hop is FE80::5111:11FF:FE11:1111

    D

    The next hop is 2001::1


    正确答案： A
    解析： 暂无解析

  • 第11题：

    单选题
    Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
    A

    Metric

    B

    Administrative distance

    C

    Timeout (seconds)

    D

    Prefix length

    E

    Interface ID


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1
    A

    EIGRP works on F0/0 and S0/0/0 without further configuration

    B

    EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE

    C

    EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE

    D

    EIGRP for IPv6 needs at least two more configuration commands before it works on R1


    正确答案： B
    解析： 暂无解析

  • 第13题：

    Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link.Which of the following commands would be needed on R1 to configure eBGP?（）

    A. router bgp 2

    B. router bgp 1

    C. neighbor 10.1 .1.2 remote - as 2

    D. neighbor 10.1.1.2 Update - source 10.1.1.1

    E. neighbor 10.1.1.2 Update- source S0/0


    参考答案：B, C

  • 第14题：

    An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（）key chain fredkey 3key - string whehewinterface fa0/0ip authenticat ion key - chain eigrp 9 fred

    A.The configuration is missing one authentication - related configuration command

    B.The configuration is missing two authentication - related configuration commands

    C.Authentication type 9 is not supported; type 5 should be u sed insteaD

    D.The key numbers must begin with key 1, so change the key 3 command to key 1


    参考答案：A

  • 第15题：

    Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1‘s configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2.Which answer gives the reason for the omission？（）

    A. R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.

    B. S0/2 may currently be in a state other than up/up.

    C. The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.

    D. S0/2 may be configured as a passive inter face.


    参考答案：B

  • 第16题：

    An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（） key chain fred key 3 key - string whehew interface fa0/0 ip authenticat ion key - chain eigrp 9 fred

    • A、The configuration is missing one authentication - related configuration command
    • B、The configuration is missing two authentication - related configuration commands
    • C、Authentication type 9 is not supported; type 5 should be u sed insteaD
    • D、The key numbers must begin with key 1, so change the key 3 command to key 1

    正确答案:A

  • 第17题：

    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1

    • A、EIGRP works on F0/0 and S0/0/0 without further configuration
    • B、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE
    • C、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE
    • D、EIGRP for IPv6 needs at least two more configuration commands before it works on R1

    正确答案:D

  • 第18题：

    Which of the following commands will cause RIPng to originate a default route advertisement whilesuppressing all other routes？（）

    • A、Rl（config-if）#ipv6 default-information originate
    • B、Rl（config-router）#ipv6 rip 〈process-name〉 default-information only
    • C、Rl（config）#ipv6 route ：：/0 null 0
    • D、Rl（config-if）#ipv6 rip 〈process-name〉 default-information only
    • E、Rl（config-router）#ipv6 rip route ；：/0 originate
    • F、Rl（config-router）#aggregate-address ：：/0 summarize-routes

    正确答案:D

  • 第19题：

    单选题
    An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（） key chain fred key 3 key - string whehew interface fa0/0 ip authenticat ion key - chain eigrp 9 fred
    A

    The configuration is missing one authentication - related configuration command

    B

    The configuration is missing two authentication - related configuration commands

    C

    Authentication type 9 is not supported; type 5 should be u sed insteaD

    D

    The key numbers must begin with key 1, so change the key 3 command to key 1


    正确答案： B
    解析： 暂无解析

  • 第20题：

    单选题
    Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）
    A

    R1 limi ts EIGRP to around 250Kbps on DLCI 102

    B

    R1 limits EIGRP to around 250Kbps on DLCI 104

    C

    R1 limits EIGRP to around 150Kbps on every DLCI

    D

    R1 does not limit EIGRP because noWAN bandwidth control has been configured


    正确答案： C
    解析： 暂无解析

  • 第21题：

    单选题
    Which of the following commands will cause RIPng to originate a default route advertisement whilesuppressing all other routes？（）
    A

    Rl（config-if）#ipv6 default-information originate

    B

    Rl（config-router）#ipv6 rip 〈process-name〉 default-information only

    C

    Rl（config）#ipv6 route ：：/0 null 0

    D

    Rl（config-if）#ipv6 rip 〈process-name〉 default-information only

    E

    Rl（config-router）#ipv6 rip route ；：/0 originate

    F

    Rl（config-router）#aggregate-address ：：/0 summarize-routes


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode. Which of the following occurs？（）
    A

    Fa0/0 fails

    B

    The command is rejecteD

    C

    The existing three neighbors fail

    D

    The neighborship with 172.16.2.20 fails and then reestablishes

    E

    None of the other answers is correct


    正确答案： B
    解析： 暂无解析

  • 第23题：

    单选题
    Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission？（）
    A

    R1 has EIGRP neighbors reachable via S0/0 and  S0/1, but not via S0/2, so it is not included.

    B

    S0/2 may currently be in a state other than up/up.

    C

    The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.

    D

    S0/2 may be configured as a passive inter face.


    正确答案： D
    解析： 暂无解析

  • 第24题：

    单选题
    Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?（）
    A

    FEA0::200:FF:FE11:0

    B

    FE80::200:FF:FE11:1111

    C

    FE80::0213:19FF:FE7B:0:1

    D

    FEB0::211:11FF:FE11: 1111


    正确答案： A
    解析： 暂无解析

相关内容